Gradall Forklift Parts

Gradall Forklift Part - All through the time when World War II caused a scarcity of laborers, the legendary Gradall excavator was born in the 1940s as the creation of two brothers Ray and Koop Ferwerda. Partners in a Cleveland, Simi Valley construction business known as Ferwerda-Werba-Ferwerda, the brothers faced a huge predicament when a lot of men left the workforce and signed up in the military, depleting existing workers for the delicate finishing work and grading on highway projects. The Ferwerda brothers decided to build an equipment which would save their business by making the slope grading job more efficient, less manual and easier.

Their initial design prototype was a machine with two beams set on a rotating platform which was affixed atop a second-hand truck. A telescopic cylinder moved the beams back and forth which allowed the fixed blade at the end of the beams to pull or push dirt. Before long enhancing the first design, the brothers made a triangular boom to add more strength. As well, they added a tilt cylinder which let the boom turn 45 degrees in either direction. A cylinder was positioned at the rear of the boom, powering a long push rod to allow the equipment to be outfitted with either a bucket or a blade attachment.

Gradall launched in the year 1992, with the introduction of the new XL Series hydraulics, the most ground-breaking adjustment in their equipment since their creation. This new system of top-of-the-line hydraulics enabled the Gradall excavator to deliver comparable power and high productivity to the more traditional excavators. The XL Series put an end to the first Gradall equipment power drawn from low pressure hydraulics and gear pumps. These traditional systems successfully handled grading and finishing work but had a difficult time competing for high productivity work.

The new XL Series Gradall excavators proved a remarkable increase in their lifting and digging ability. These versions were made with a piston pump, high-pressure hydraulics system that showed huge improvements in boom and bucket breakout forces. The XL Series hydraulics system was even developed with a load-sensing capability. Traditional excavators utilize an operator so as to choose a working-mode; where the Gradall system could automatically adjust the hydraulic power meant for the task at hand. This makes the operator's overall task easier and likewise saves fuel at the same time.

Once their XL Series hydraulics came onto the market, Gradall was basically thrust into the highly competitive market of equipment meant to deal with pavement removal, excavation, demolition as well as other industrial tasks. Marketability was further improved with their telescoping boom because of its exclusive ability to work in low overhead areas and to better position attachments.

Click to Download the pdf

Forklift Parts

Industrial Forklift Parts

Industrial Forklift Part - Now, there are numerous kinds of lifting machinery utilized lift and transfer merchandise and materials. Common machines utilized on the jobsite will consist of pallet trucks, chain slings, cranes, pulling machines and shackles. The importance of lifting machinery so as to minimize the use of manual labor and making sure industrial safety is paramount. The Lifting...

More

---

Forklift Fork Extension

Forklift Fork Extensions - Lift Truck extensions are a excellent choice when there is a need to reach further than your existing blades would allow. In several situations when you have a load which exceeds more than can be securely raised on your forklift, an extension can help you complete your task safely. Increasing Forklift Efficiency Extensions will offer added...

More

---

Straight Boom Lift Parts

Parts for Straight Boom Lifts - Boom lifts are also referred to as aerial work platforms. They can comprise a platform or bucket that is attached to the end of a hydraulic lifting system. This kind of aerial work platform is normally found mounted on a flat-back pickup van, likewise referred to as a "Self Drive." Boom lifts are also...

More

---

Parts for Full Rise Scissor Lift

Full Rise Scissor Lift Part - Scissor lift pallet vehicles are made to be able to move and stack pallets with a built-in raising apparatus that permits the pallets to be elevated. This equipment is really effective for working in limited spaces that will not allow for a full-sized forklift. The scissor pallet vehicle is very efficient at loading and...

More

---

Forks for Forkflifts

Forklift Forks - Sometimes equipment parts get old from use and so they require changing. Companies can usually safe fairly a bit of money by simply replacing individual parts as they wear out versus obtaining a completely new device. Additional savings are accessible usually when replacing parts, there's the option to buy used parts rather than new ones. There are...

More

---

Parts for Articulated Boom Lift

Articulated Boom Lift Part - Boom vehicle are often used by phone, cable and utilities firms as they have extended folded arms which are generally folded over the roofs of company vehicles. On the end of the extension of extendable arms frequently sits a bucket-like apparatus. When a bucket vehicle has an extendable boom mounted the roof this is sometimes...

More

---

Parts for Propane Forklift

Propane Forklift Part - Propane lift trucks use an engine that operates utilizing propane gas. This propane stores in a pressurized tank and could be refilled easily. As soon as the propane gas is pushed into the engine, it is converted into vapour while it de-pressurizes. Using a throttle, the flow of vapour can be managed. Inside the engine, the...

More

---

Adjustable Booms

Adjustable Boom - For many businesses, a very useful piece of equipment is the adjustable boom forklift which can lift and reposition heavy items all over. The forklift mechanism is a very useful tool on its own, equipped with powered forks on the front of the device. These prongs could be slid under really heavy loads and afterward raised. This...

More

---